QIKFIT saves you time during installation and hassle if you need to respecify. Modules can be swapped & changed when needed with blanks available to fill unused space.
Adding power to your workbench is easy. All you need to do is measure and cut the aperture, clip in QIKFIT power modules, then connect the wires.
You can create dozens of configurations with the QIKFIT range. We are convinced that you’ll be able to create a custom solution that meets your needs.
In this workbench, the QIKFIT modules were clipped into the cut-out in the metal panel. Featured are our QIKFIT POWER MODULE, Q30 E-STOP, QF30 CUSTOM (to turn on the above lighting), and QF30 PROTECT.
See components >>
Choose any suitable combination of QIKFIT power and USB modules and data /AV.
See components >>
Ready to add QIKFIT to your workbenches? Find all the technical information such as cutout sizes and correlating configurations here. If you can’t find what you are looking for, get in touch with our expert team who are here to help you.
QF30 specifications:
QF30 E-STOP | Through current rating Rating 230V 10A Overload protection 10A thermal on both L&N |
QF30 PROTECT | RCD 30mA type AC or type A |
QF30 CUSTOM + Switch | 230V 16A Double Pole |
QF15 TUF 25W specifications:
USB Charging Outlets | 1 x Type A Female |
Charging Current | Type A 5V up to 2.5A |
Rated Total Output Power | 25W |
AC Voltage Range | 200-240VAC at 50/60Hz |
AC Input Current (Full Load) | Maximum 0.6A |
Efficiency | Up to 90% |
Environment | 0 – 30C / 85% Relative Humidity |
Standby Power | 0.05W |
QF15 TUF HP specifications:
USB Charging Outlets | 1 x Type C (Reversible) |
Power In connector | Male GST18i3 AC connector |
Rated Total Output Power | 65W MAX |
| Output Voltages & Currents | (USB-C or USB-A Port single used): USB-C: PD3.0: 5Vdc/3A or 9Vdc/3A or 12Vdc/3A or 15Vdc/3A or 20Vdc/3.25A QC2.0/QC3.0: 5Vdc/3A or 9Vdc/3A or 12Vdc/3A USB-A: 5Vdc/2.4A Output (USB-C and USB-A Port both used): USB-C: PD3.0: 5Vdc/3A or 9Vdc/3A or 12Vdc/3A or 15Vdc/3A or 20Vdc/2.25A QC2.0/QC3.0: 5Vdc/3A or 9Vdc/3A or 12Vdc/3A USB-A: 5Vdc/2.4A |
| Over voltage category (OVC): | OVC III |
| Input voltage | 100-240V~, 50/60Hz, MAX1.6A |
USB Connector Min. Insertions | Type A 10,000 |
Over Current Protection | Yes. Digital control at 3.3A. Auto reset with LED flash. |
Short Circuit Protection | Yes. Digital control at 3.3A. Auto reset. |
Over Temperature Protection | Yes |
Rated Operating Temperature | 0° TO 25°C |
Certifications – Safety | IEC 62368-1 : 2014 |
Certifications –EMC | EN61204 : 2018 FCC part 15 (B) |
Certifications ROHS | EU 2015/863 |
| User Replaceable USB module | No |
QF05 TUF HP specifications:
USB Charging Outlets | 1 x Type C (Reversible) |
Power In connector | Male GST08 DC connector |
Rated Total Output Power | 72W MAX |
| Output Voltages & Currents | TYPE C: MAX 60W TYPE A: MAX 12W |
| Input voltage | 24 – 30V DC |
USB Connector Min. Insertions | Type A 10,000 |
Over Current Protection | Yes. Digital control at 3.3A. Auto reset with LED flash. |
Short Circuit Protection | Yes. Digital control at 3.3A. Auto reset. |
Over Temperature Protection | Auto Power Reduction to PD 45W Mode. |
Rated Operating Temperature | 0° TO 25°C |
User Replaceable USB module | Yes |
Certifications – Safety | IEC 62368-1 : 2014 |
Certifications –EMC | EN61204 : 2018 |
Certifications ROHS | EU 2015/863 |
Note: Cutouts should be made in multiples of QF05 (ie: ## x 26.5mm, minus 2mm). STANDARD cutouts should be no longer than QF60, please contact us for guidance for cutouts exceeding this size.
QIKFIT 25 cutout (130.5mm x 41.5mm)
• 5 x QF05
•1 x QF 2G
• 1 x QF25 BLANK
QIKFIT 30 cutout (157mm x 41.5mm)
• 1 x QF 2G
• 1 x QF05• 1 x QF30 E-STOP
• 1 x QF30 RCD/MCD
QIKFIT 45 cutout (236.5mm x 41.5mm)
• 1 x QF 2G, 1 x QF15 TUF, 1 x QF05
• 1 x QF 3G, 2x QF05
• 1 x QF45 BLANK
QIKFIT 60 cutout (316mm x 41.5mm)
• 1 x QF30 SWITCH, 1 x QF 2G (1 x spacer required), 2 x QF05
• 1 x QF30 RCD/MCB, 1 x QF3G (1 x spacer required), 1 x QF45 BLANK, 3 x QF05
• 1 x QF 2 G*, 1 x QF3G (1 x spacer required)
• 1 x QF45 BLANK, 3 x QF05
* Locking clips must be removed before assembly
Chose from our on surface power units and simply clamp your power solution in place.
On surface range >>
Don’t be shy, say hi 
We are excited to hear about your ideas. Drop a line below and our expert team will be in touch.
OE House,
Calder Park,
Thomas Maddison Ln,
Durkar,
Wakefield
WF4 3GH
OE Showroom
1a Briset Street
London
EC1M 5NR
UK
